Mechanical seals Type KRPT 1
Construction: Cartridge Design, metal parts SS, built in Impellor, secondary seals of heat resistant rubber.
Application: Used in accordance with API 682/ ISO 21049, for installation in the pumping Equipment of oil and petrochemical industry. Sealing Environment: hazardous, toxic, abrasive, corrosive, non lubricating Temperature -40*C to 200 *C, Pressure 35 Kg/Sq cm, Sliding speed Up to 50M/sec

Mechanical Seals SMPT1
Construction: Cartridge design with welded metal bellows and secondary seals, built in impeller, metal parts SS Application: Used in accordance with API 682/ ISO 21049, for installation in the pumping equipment of oil and petrochemical industries
Sealing Environment: Hazardous, toxic, abrasive, corrosive, non lubricating medium Temperature -75*C to 400*C, Pressure 60 Kg/ sq cm, Sliding speed up to 25 M/sec

Mechanical Seals SMPV 1
Construction: Cartridge design, built in impeller, with welded metal bellows with support seals, (throttle seals), with steam supply as protective environment, metal parts SS
Application: Used in accordance with API 682/ ISO 21049, for installation in the pumping equipment of oil, refineries and petrochemical industries in conditions of high & low temperatures Sealing Environment: Hazardous, toxic, abrasive, corrosive, non lubricating medium, viscous Temperature -75*C to 450*C, Pressure 60 Kg/ sq cm, Sliding speed up to 50 M/sec

Mechanical Seals SMPS 1
Construction:Cartridge design, with welded metal bellows with outer seal running dry , metal parts SS
Application: Used in accordance with API 682/ ISO 21049, for installation in the pumping equipment of oil, refineries and petrochemical industries in conditions of high & low temperatures Sealing Environment: Hazardous, toxic, abrasive, corrosive, non lubricating medium, viscous Temperature -75*C to 450*C, Pressure 60 Kg/ sq cm, Sliding speed up to 50 M/sec Excludes the cost of water cooling system

Mechanical Seals KRPD 10
Construction: Cartridge design, balanced, with secondary seal of different materials, Metal components: 12X18H10T (K), 10X17H13M2T (E) Springs: 12X18H10T (K), 10X17H13M2T (E) Secondary seals: ethylene rubber (1), butadiene rubber (2), Fluoroelastomers (3), V - shaped fluoroplastic sleeves ,Friction pair: Graphite impregnated with metal , graphite impregnated with resin , Silicon Carbide SiC ,Tungsten Carbide
Application:For installation in the dissolvers, mixers, taps, reactors for chemical and petrochemical industries. Sealing Environment: Different environments and their vapors, which in the atmosphere is not permissible

Temperature -75*C to 200 *C, Pressure 70 Kg/ sq cm, Sliding Speed 2.5 M/sec Complies with DIN 24960, EN 12756 and ISO 3069 (at the radial size)

Mechanical Seals Type SMPD 35
Double mechanical seals, cartridge, with welded metal bellows,. It is recommended to use different equipment (dissolvers, stirrers, mixers, reactors), chemical and petrochemical plants in low, medium and high temperature.
Sealed medium: Different environments and their vapors, which in the atmosphere is not permissible.
Temperature from -75 to 360 *C
Pressure to 60 kg/cm2
Sliding velocity to 50 m / s

Metal parts: Stainless steel , Bellows: 12H18N10T, 36NKhTYu

BELLOWS Mechanical Seals Type SM.51
Single mechanical seals with a non-rotating welded metal bellows. Designed for use in tank mixers in refineries, petrochemical and other industries, Temperature -40 *C to 50 *C, Pressure up to 2 kg/ sq cm, shaft speed up to 500 RPM , Specially designed fixed welded bellows provides compensation for axial movement of the agitator shaft up to 30 mm

Mechanical Seals Type SRMP 15
Special Single mechanical seals, cartridge, Balanced, for a variety of contaminated liquids. For installation in pumps, mixers, and other equipment with rotating shafts. Sealed medium: Environments with high content of solids and fibers, waste water, sludge, clay solutions.. It is used in the energy, petrochemical and metallurgical industries & in the oil fields. Temperature -40*C to 220*C, Pressure 25 Kg/ sq cm, Sliding Speed 25 M / sec Shaft dia: up to 200 mm . Same seal can be used for both the directions of rotation

Mechanical Seals Type KRPSD
Dual mechanical seals, cartridges design. for installation in pumps, mixers, and other equipment with rotating shafts, Sealed medium: Various environmental chemical, petrochemical, oil refining, pharmaceutical, pulp and paper, and food industries, toxic liquids and hazardous gases, viscous and polymer liquids. Temperature -- 40*C to 220*C, Pressure 25 Kg/ sq cm, Sliding Speed up to 25 M / sec Shaft dia: up to 100 mm . Same seal can be used for both the directions of rotation.

Mechanical Seals Type RFTF
Single Split mechanical seals, cartridges. Design for important equipment, which is very difficult to dismantle, but should be quickly repaired. Sealed medium: Various clean environment. oil, water, sea water . Temperature -40*C to 220*C, Pressure 25 Kg/ sq cm, Sliding Speed up to 25 M / sec, Shaft Dia up to 195 mm

Bellows Mechanical Seal Type RE 2
Single mechanical seals for general purpose, rotary elastomer bellows, with a central spring and secondary seal of various grades of rubber. Sealing medium: Water and waste water, solvent, refrigerants, weak acids and bases, as well as their solutions, solutions of salts, crude oil, petroleum products (petrol, kerosene, diesel fuel), food and fluids, etc. Temperature -40 to 160 C Pressure to 12 kg/cm2 Sliding velocity of 10 m / s. Available in shaft dia up to 100 mm

Mechanical Seals Type KR 4 & KRA 4
Single mechanical seals with a wavy spring, general purpose, unloaded (type KRA.4) or unloaded (type KR.4), with secondary seals of different grades of rubber. For installation in pumps, agitators, and other equipment with rotating shafts. Sealing Medium: oil, water, weak acids and alkalis, organic chemistry, food protection, alcohol and other liquids with low solids content, and low viscosity. Temperature: from -75 to 220 C, Pressure: 50 kg/cm2, Sliding Speed: up to 25 m / s

Mechanical Seals Type KR 5 & KRA 5
Single mechanical seals with a central spring general purpose, unloaded (type KRA.5) or unloaded (type KR.5), with secondary seals of different grades of rubber, for installation in pumps, agitators, and other equipment with rotating shafts. Sealed medium: Liquids with a high content of solid or hazardous highly corrosive environment. waste water, crude oil, alkaline solutions, hydrochloric and sulfuric acid, etc. Temperature: from -75 to 220 C, Pressure: 50 kg/cm2, Sliding Speed: up to 25 m / s. Shaft dia up to 90 mm

Mechanical Seals Type SRM 1
Single mechanical seals with a set of small springs, protected from the environment elastomer bellows, Balanced, with secondary seals of different grades of rubber. For installation in pumps, agitators, and other equipment with rotating shafts. Sealed medium: Environments with high content of solid or highly viscous medium, waste water, pulp slurry, crude oil, paint, food protection and paper industry. Temperature: from -40 to 220 C, Pressure: 50 kg/cm2, Sliding Speed: up to 25 m / s

Single Mechanical Magnetic Seals Type KRA 30
Single magnetic face seals with secondary seals of fluorine. Sealed medium: mineral and synthetic oils and lubricants. Available for motors, gearboxes, fans, steam turbines, pumps, motors instead of conventional cup-type and labyrinth seals. Temperature: -40 to 150 C, Pressure: up to 3 kg/cm2, Sliding Speed: up to 30 m / s. Shaft dia up to 150 mm. Metal parts: Steel 45 or others Secondary seals: Fluoroelastomers , Magnets: Rare-earth metals , Friction pair: steel, tungsten carbide

No leakage is ensured by continuous contact of rubbing surfaces, which is achieved through the use of modern magnetic technology and quality materials.

Cryogenic Mechanical Seals Type SMS 49
Single-contact face seals with non-rotating welded metal bellows. Recommend using in a cryogenic pumping equipment metallurgical, petrochemical and refining industries in the low (negative) temperature during pumping liquefied gases: nitrogen, oxygen, argon and hydrogen. Temperature: - 196 *C, Pressure: 6 kg/cm2, Shaft speed: up to 10 000 rpm

Cryogenic Mechanical Seals Type SMPS 61
Single non contact cartridge mechanical seals with a non-rotating welded metal bellows, recommend using in a cryogenic pumping equipment metallurgical, petrochemical and refining industries in the low (negative) temperature during pumping liquefied gases: nitrogen, oxygen, argon and hydrogen. Temperature: - 196*C, Pressure: 6 kg/cm2 Shaft speed: up to 10 000 rpm. Reliable and cost-effective alternative to contact type face seal.